Description

The Function of the fuel pump is to supply fuel at a certain pressure to the engine fuel injection system. However,the fuel pump have a limited life.If you notice any of the following signs with your car: (1).Engine Sputtering at High Speeds (2).Decreased Fuel Pressure (3).Losing Power when the Vehicle is under Stress (4).Inability to accelerate (5).Decreasing Gas Mileage (6).Engine Not Starting This may indicate that you need to replace the fuel pump Fuel Pump Replacement Guideline: Please Note the following before replacing the fuel pump: 1.Ensure that you are in a well ventilated and level work area. Fuel Pump Fit For Hyundai Santa Fe L4 2.4L 2013 2014 2015 2016 2017 2018 The Function of the fuel pump is to supply fuel at a certain pressure to the engine fuel injection system. However,the fuel pump have a limited life.If you notice any of the following signs with your car: (1).Engine Sputtering at High Speeds (2).Decreased Fuel Pressure (3).Losing Power when the Vehicle is under Stress (4).Inability to accelerate (5).Decreasing Gas Mileage (6).Engine Not Starting This may indicate that you need to replace the fuel pump Fuel Pump Replacement Guideline : Please Note the following before replacing the fuel pump: 1.Ensure that you are in a well ventilated and level work area. 2.Use approved safety glasses or goggles when working on any motor vehicle. 3.The gasoline is sucked out of the tank and stored in a container dedicated to gasoline. Picture(A) Disconnect the ground ( negative ) cable of the battery and ensure that it does not accidentally spark while working. Picture( B ) Locate and remove gas tank filler neck mounting bolts or remove the filler tube from the tank. This will aid the fuel removal especially if you had problems accessing through the filler neck. Picture( C ) Located the electrical connector for the fuel pump and fuel level sender which will be in the same wiring harness. If access if difficult or you can't see them wait until the tank is lowered slightly to undo the connector. Inspect electrical connector for burns or heated spots and replace if damaged. A burned connector can cause a pump to fail intermittently. Picture( D ) There will be fuel vapor lines as part of the EVAP system these will need to be removed or disconnected. Picture( E ) Locate and release tank holder supports, there are two in most cases. Remove the mounting bolts at this point the tank will become loose but may not come out. Picture( F ) Lower the tank and release top mounted fuel lines or electrical connectors if any. Continue to remove the tank. Picture( G ) Remove the tank, this will expose the fuel pump retainer ring. Use an aerosol cleaner to remove dirt and debris from the area. This will keep the inside of the fuel tank clean when performing the repair. Picture( H ) Remove fuel pump mounting bolts or retainer ring to access the fuel pump module and remove the unit. Use a hammer and punch to remove the ring counterclockwise. Picture( I ) Remove the fuel pump which will be attached to the mounting plate or positioned down inside the tank held by plastic retainer clips. Picture( J ) Remove the fuel pump from the tank. table#Attrid1288332 {border-collapse:separate} table#Attrid1288332 tr:last-child td:last-child{border-bottom-right-radius: 10px;} table#Attrid1288332 tr:last-child td:first-child{border-bottom-left-radius: 10px;} table#Attrid1288332 tr:nth-of-type(1n){} table#Attrid1288332 tr:nth-of-type(2n){} table#Attrid1288332 td{padding: 3px;} table#Attrid1288332{font-size:12px !important;font-family:Arial !important;color:#4c4c4c !important;text-align:left !important;} table#Attrid1288332 td:first-child{font-weight: 900; !important;;padding:3px;border:1px none ;} #m_pre1288332{border:1px none ;overflow: hidden;border-radius: 10px;} Item Specifics Type Fuel Pump Placement on Vehicle Fuel Tank Fuel Type Gasoline Fitment Type Direct Replacement Mounting Hardware Included No OE/OEM Part Number E9217MP77019M,FG1904,SP3085M Custom Bundle No Gasket Included No Modified Item No Brand Fuel_Kingparts Voltage 12 V Internal Or External Internal Universal Fitment No Quantity Per Application 1 Wiring Harness Included No Outlet Size 5/16 Minimum Order Quantity 1 Inlet Count 1 Outlet Count 1 Drive Type Electrical Manufacturer Warranty 3 Years Manufacturer Part Number FK11624601G Fuel Level Sender Resistance 8-200 ohm Flow Rate 55-65 gph Pressure 70-80 psi Amperage 10 A Payment We only accept payment through PayPal. Shipping All domestic orders will be shipped via USPS, UPS or Fedex from our US warehouse and usually arrives to your door in about 2-7 business days. Returns All of our brand new items come with a 60-Days money-back guarantee. Contact Us Any question, please contact us by email on working days. Warning WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov. Best Sales For Dodge Ram 1500 2500 5.2L 5.9L 1996-1997 Fuel Pump w/Sending Unit E7093M USD 48.99 For Ford Expedition 5.4L 2003 2004 Fuel Pump Assembly E2360M USD 38.49 For Ford F-150 5.4L 4.6L 2009-2010 F-150 3.7L 5.0L 6.2L 2011-2014 Fuel Pump USD 49.49 For Jeep Liberty 3.7L 2008-2012 Dodge Nitro 3.7L 4.0L 2007-2011 Fuel Pump USD 45.99 For Ford F-150 2004-2008 4.6L 5.4L 2005-2008 4.2L Fuel Pump E2434M USD 41.99 Newly Listed For Kia Forte 2.0L 2.4L w/o Calif 2010 2011 2012 2013 Fuel Pump Moudle Assembly USD 40.24 Fuel Pump Assembly For Ford F-250 Super Duty F-350 Super Duty 6.2L 2017-2020 USD 65.99 For 1995 Dodge Ram 1500 3.9L 5.2L 5.9L Ram 2500 5.2L Ram 3500 8.0L Fuel Pump USD 49.75 For Kia Rondo 2.4L 2007 2008-2010 Electrical Fuel Pump Module Aseembly E8786M USD 86.99 For Ford Mustang 3.8L 2.3L 4.6L 5.0L 1987-1997 Electrical Fuel Pump Aseembly USD 34.99 Terms & Contact Payment Policy Shipping Policy Return Policy FAQ About Us Fuel Pump Fit For Hyundai Santa Fe L4 2.4L 2013 2014 2015 2016 2017 2018 The Function of the fuel pump is to supply fuel at a certain pressure to the engine fuel injection system. However,the fuel pump have a limited life.If you notice any of the following signs with your car: (1).Engine Sputtering at High Speeds (2).Decreased Fuel Pressure (3).Losing Power when the Vehicle is under Stress (4).Inability to accelerate (5).Decreasing Gas Mileage (6).Engine Not Starting This may indicate that you need to replace the fuel pump Fuel Pump Replacement Guideline : Please Note the following before replacing the fuel pump: 1.Ensure that you are in a well ventilated and level work area. 2.Use approved safety glasses or goggles when working on any motor vehicle. 3.The gasoline is sucked out of the tank and stored in a container dedicated to gasoline. Picture(A) Disconnect the ground ( negative ) cable of the battery and ensure that it does not accidentally spark while working. Picture( B ) Locate and remove gas tank filler neck mounting bolts or remove the filler tube from the tank. This will aid the fuel removal especially if you had problems accessing through the filler neck. Picture( C ) Located the electrical connector for the fuel pump and fuel level sender which will be in the same wiring harness. If access if difficult or you can't see them wait until the tank is lowered slightly to undo the connector. Inspect electrical connector for burns or heated spots and replace if damaged. A burned connector can cause a pump to fail intermittently. Picture( D ) There will be fuel vapor lines as part of the EVAP system these will need to be removed or disconnected. Picture( E ) Locate and release tank holder supports, there are two in most cases. Remove the mounting bolts at this point the tank will become loose but may not come out. Picture( F ) Lower the tank and release top mounted fuel lines or electrical connectors if any. Continue to remove the tank. Picture( G ) Remove the tank, this will expose the fuel pump retainer ring. Use an aerosol cleaner to remove dirt and debris from the area. This will keep the inside of the fuel tank clean when performing the repair. Picture( H ) Remove fuel pump mounting bolts or retainer ring to access the fuel pump module and remove the unit. Use a hammer and punch to remove the ring counterclockwise. Picture( I ) Remove the fuel pump which will be attached to the mounting plate or positioned down inside the tank held by plastic retainer clips. Picture( J ) Remove the fuel pump from the tank. table#Attrid1288336 {border-collapse:separate} table#Attrid1288336 tr:last-child td:last-child{border-bottom-right-radius: 5px;} table#Attrid1288336 tr:last-child td:first-child{border-bottom-left-radius: 5px;} table#Attrid1288336 tr:nth-of-type(1n){padding: 5px!important;background:#ffffff;} table#Attrid1288336 tr:nth-of-type(2n){padding: 5px!important;background:#f7fffb;} table#Attrid1288336 td div{padding: 5px;text-align:;} table#Attrid1288336 {font-family:Arial !important;font-size:16px !important;color:#000000 !important;text-align:left !important;} table#Attrid1288336 td:first-child{} table#Attrid1288336 td{padding:12px;border:1px solid #000000;} Item Specifics Type : Fuel Pump Placement on Vehicle : Fuel Tank Fuel Type : Gasoline Fitment Type : Direct Replacement Mounting Hardware Included : No OE/OEM Part Number : E9217MP77019M,FG1904,SP3085M Custom Bundle : No Gasket Included : No Modified Item : No Brand : Fuel_Kingparts Voltage : 12 V Internal Or External : Internal Universal Fitment : No Quantity Per Application : 1 Wiring Harness Included : No Outlet Size : 5/16 Minimum Order Quantity : 1 Inlet Count : 1 Outlet Count : 1 Drive Type : Electrical Manufacturer Warranty : 3 Years Manufacturer Part Number : FK11624601G Fuel Level Sender Resistance : 8-200 ohm Flow Rate : 55-65 gph Pressure : 70-80 psi Amperage : 10 A Payment Shipping Returns Contact Us Warning We only accept payment through PayPal. All domestic orders will be shipped via USPS, UPS or Fedex from our US warehouse and usually arrives to your door in about 2-7 business days. All of our brand new items come with a 60-Days money-back guarantee. Any question, please contact us by email on working days. WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov. All rights reserved.